Chainsaw Dies when I Give it Gas (Guide 2022)

Have you ever gone to start your chainsaw, only to have it just turn over and not start? You’re not alone. In fact, this is a common problem that many millers and woodcutters face when operating a chainsaw. There are a few reasons why your chainsaw might die when you try to give it gas, but don’t worry – there are also a few ways to fix the issue. In this blog post, we’ll discuss the most common causes of chainsaw die-offs and how to prevent them from happening.

>>>> How are Chainsaw Bars Measured?

There are many reasons why a chainsaw might die when you try to give it gas.

Keeping in mind here we come up with the top 10 reasons.

Why chainsaw might die when you give it gas?

  1.  Wrong Fuel Mixture

One of the most common reasons why chainsaws die when you try to give them gas is because of the wrong fuel mixture.

The fuel mixture for a chainsaw is different than that of a regular gasoline engine – it needs to be more explosive in order to power the chainsaw’s blade.

If you’re using the wrong fuel mixture, your chainsaw will likely turn over but not start.

To fix this, simply drain the chainsaw’s tank and refill it with the correct fuel mixture.

  1. Old or Dirty Fuel

Another common reason for chainsaws dying when you try to give it gas is an old or dirty fuel.

Over time, gasoline can break down and become less explosive.

This means that it won’t be able to power your chainsaw’s blade as effectively, causing the chainsaw to die.

To fix this, simply drain the chainsaw’s tank and refill it with fresh gasoline.

  1. Bad Spark Plug

A bad spark plug is another common reason why chainsaws die when you try to give it gas.

The spark plug helps ignites the fuel mixture in the chainsaw’s engine, so if it’s not working properly, the chainsaw won’t start.

>>>> How To Tune A Chainsaw?

To fix this, simply replace the spark plug with a new one.

  1. Clogged Air Filter

A clogged air filter is another common reason for chainsaws dying when you try to give it gas.

The air filter prevents dirt and debris from getting into the chainsaw’s engine, so if it’s clogged, the engine won’t be able to breathe properly.

To fix this, simply clean or replace the air filter.

  1. Dirty Chainsaw Blade

A dirty chainsaw blade is another common reason why chainsaws die when you try to give it gas.

If the chainsaw’s blade is covered in dirt and debris, it won’t be able to cut through the wood properly.

To fix this, simply clean the chainsaw’s blade with a rag or brush.

  1. Blocked Fuel Line

A blocked fuel line is another common reason why chainsaws die when you try to give it gas.

If the fuel line is blocked, the chainsaw won’t be able to get the gasoline it needs to run.

To fix this, simply clean or replace the fuel line.

  1. Low Oil Level

A low oil level is another common reason why chainsaws die when you try to give it gas.

The chainsaw needs oil to lubricate its moving parts, so if the oil level is low, the chainsaw will seize up and die.

To fix this, simply add more oil to the chainsaw’s reservoir.

  1. Worn or Broken Chain

A worn or broken chain is another common reason why chainsaws die when you try to give it gas.

If the chain is worn or broken, it won’t be able to cut through the wood properly, causing the chainsaw to stall.

To fix this, simply replace the chainsaw’s chain.

  1. Clogged Muffler

A clogged muffler is another common reason why chainsaws die when you try to give it gas.

If the muffler is clogged, the chainsaw’s engine won’t be able to breathe properly, causing it to stall.

To fix this, simply clean or replace the chainsaw’s muffler.

  1. Dead Battery

A dead battery is another common reason why chainsaws die when you try to give it gas.

If the chainsaw’s battery is dead, it won’t be able to start the chainsaw’s engine.

To fix this, simply replace the chainsaw’s battery with a new one.

These are the most common reasons why chainsaws die when you try to give it gas. If you’re having this problem, check to see if any of these issues are the cause. With a little troubleshooting, you should be able to get your chainsaw up and running again in no time!

How to check if the chainsaw is getting enough gas?

One way to check if your chainsaw is getting enough gas is to listen to the engine. If the chainsaw’s engine is sputtering or sounds like it’s about to die, it’s likely that it’s not getting enough gasoline. Another way to check is to look at the chainsaw’s fuel tank. If the tank is empty or nearly empty, it’s likely that the chainsaw isn’t getting enough gas. Finally, you can try starting the chainsaw and seeing if it dies when you give it gas. If it does, then it’s likely that the chainsaw isn’t getting enough gasoline.

Conclusion:

In the end, we hope that this guide was helpful in teaching you the most common reasons why chainsaws die when you try to give it gas, as well as how to troubleshoot and fix these issues. If you’re still having trouble with your chainsaw, feel free to contact a professional for further assistance. Until then, happy chainsawing!

FAQs:

Why does my chainsaw keep dying?

There are a few reasons why your chainsaw might keep dying, but the most common reason is that it’s not getting enough gasoline. Other common reasons include a clogged air filter, dirty chainsaw blade, blocked fuel line, low oil level, and a worn or broken chain.

How do I fix my chainsaw if it keeps dying?

If your chainsaw keeps dying, you should first check to see if it’s getting enough gasoline. If not, fill up the chainsaw’s fuel tank and try again. If the chainsaw still dies, check for other common issues like a clogged air filter, dirty chainsaw blade, blocked fuel line, and low.

Related:.  How To Chainsaw Carve A Bear

Leave a Comment